收藏本站
71M6545/71M6545H Data Sheet
2.5
2.5.1
On-Chip Resources
Physical Memory
2.5.1.1 Flash Memory
The 71M6545/H includes 64 KB of on-chip flash memory. The flash memory primarily contains MPU and
CE program code. It also contains images of the CE RAM and I/O RAM. On power-up, before enabling
the CE, the MPU copies these images to their respective locations.
Flash space allocated for the CE program is limited to 4096 16-bit words (8 KB). The CE program must
begin on a 1-KB boundary of the flash address space. The CE_LCTN[5:0] ( I/O RAM 0x2109[5:0] ) field
defines which 1-KB boundary contains the CE code. Thus, the first CE instruction is located at
1024* CE_LCTN[5:0] .
Flash memory can be accessed by the MPU, the CE, and by the SPI interface (R/W).
Table 37: Flash Memory Access
Access by
MPU
CE
SPI
Access
Type
R/W/E
R
R/W/E
Condition
W/E only if CE is disabled.
Access only when SFM is invoked (MPU halted).
Flash Write Procedures
If the FLSH_UNLOCK[3:0] (I/O RAM 0x2702[7:4]) key is correctly programmed, the MPU may write to the
flash memory. This is one of the non-volatile storage options available to the user in addition to external
EEPROM.
The flash program write enable bit, FLSH_PSTWR (SFR 0xB2[0]), differentiates 80515 data store instructions
(MOVX@DPTR,A) between Flash and XRAM writes. This bit is automatically cleared by hardware after
each byte write operation. Write operations to this bit are inhibited when interrupts are enabled.
If the CE is enabled ( CE_E = 1, I/O RAM 0x2106[0] ), flash write operations must not be attempted unless
FLSH_PSTWR is set. This bit enables the “posted flash write” capability. FLSH_PSTWR has no effect when
CE_E = 0). When CE_E = 1, however, FLSH_PSTWR delays a flash write until the time interval between
the CE code passes. During this delay time, the FLSH_PEND ( SFR 0xB2[3] ) bit is high, and the MPU
continues to execute commands. When the CE code pass ends (CE_BUSY falls), the FLSH_PEND bit
falls and the write operation occurs. The MPU can query the FLSH_PEND bit to determine when the
write operation has been completed. While FLSH_PEND = 1, further flash write requests are ignored.
Updating Individual Bytes in Flash Memory
The original state of a flash byte is 0xFF (all bits are 1). Once a value other than 0xFF is written to a flash
memory cell, overwriting with a different value usually requires that the cell be erased first. Since cells
cannot be erased individually, the page has to be first copied to RAM, followed by a page erase. After
this, the page can be updated in RAM and then written back to the flash memory.
Flash Erase Procedures
Flash erasure is initiated by writing a specific data pattern to specific SFR registers in the proper sequence.
These special pattern/sequence requirements prevent inadvertent erasure of the flash memory.
The mass erase sequence is:
?
?
46
Write 1 to the FLSH_MEEN bit ( SFR 0xB2[1] ).
Write the pattern 0xAA to the FLSH_ERASE ( SFR 0x94 ) register.
The mass erase cycle can only be initiated when the ICE port is enabled.
v2
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
720-10007-00300 CBL D-SUB 9PIN FMAL-25PIN FML 3M
720-10010-00025 CBL DSUB 9PIN FML-25PIN MAL .25M
720-10020-00300 CBL DSUB 9PIN FML-9PIN MALE 3M
720-10021-00300 CBL DSUB 9PIN FML-9PIN FEMAL 3M
72231-0881 8 POS T/P SHLD 4 GR ASSY
7250B PANEL KIT BOTTOM FOR R-1220 CASE
731-10061-00200 CBL DSUB HD 15FEMAL-15MALE 2.0M
73304-111 MJ HOR ESMT 8/8 H/O T&R
相关代理商/技术参数
71M6545-IGTR/F 功能描述:计量片上系统 - SoC Metrology Proc. (3P 64K Flsh .1%) RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6545T-IGT/F 制造商:Maxim Integrated Products 功能描述:METROLOGY PROCESSORS - Rail/Tube
71M6545T-IGTR/F 制造商:Maxim Integrated Products 功能描述:3-PHASE AFE, 32KB FLASH, PRES TEMP SENSOR - Tape and Reel
71M6601 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring
71M6601-IF 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring
71M6601-IL 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring
71M6601-IL/F 功能描述:模数转换器 - ADC Isolated Sensor IC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
71M6601-ILF 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring